Square Beadboard Garden Planter – Blog – homeandawaywithlisa – Bitcoin Value
Garden Planters Diy Homemade

Square Beadboard Garden Planter – Blog – homeandawaywithlisa

Square Beadboard Garden Planter – Blog – homeandawaywithlisa



With spring here I have been wanting to spruce up my front yard and I had an inkling to try building a garden planter for myself for my front porch steps. On my Yard and Garden Pinterest board I had pinned a few planters that I drew some inspiration from. I liked the beadboard sides from the planter I pinned from Plow and Hearth and the legs that raised the planter off the ground that I pinned from the Simply Planters.

After doing a little sketching I came up with a design that I liked that also fit the space that I was planning on putting the planter on my front steps. I have shared my supply and cut list, but it would be very easy to resize the dimensions if you wanted to make a bigger planter.

Supply List:

1 – 2×2 @ 4 feet long

1 – 1×2 @ 8 feet long

1 – 1×3 @ 8 feet long

1-1/4″ pocket hole screws

Brad nails

Wood glue

Cut List:

4 – 9″ x 9″ pieces of beadboard for sides

8 – 1×2 @ 9″ for side supports

3 – 1×3 @ 9-3/8″ for bottom slats

4 – 1×3 with 45° mitered ends @ 9″ (measured from short side), 14″ (measured from long side) for top

4 – 2×2 @ 11-1/2″ for legs

To start I put some wood glue on the back of the side supports and attached one to the top and bottom of each piece of beadboard.

I aligned the top support flush with the top of the beadboard and the bottom one I overhung by 3/4″ which left me space to attach the bottom slats later. I then clamped the supports to the beadboard while the glue dried.

Next, I used my Kreg Jig to drill pocket holes on both sides at the top and bottom of each side beadboard piece. For two of the sides I attached the legs with pocket hole screws, aligned flush with the top.

I then attached the two remaining sides to one of the sides with legs using pocket hole screws.

I then attached the last side to complete making the box of the planter.

To make the top I put some wood glue on the mitered ends, clamped it all together into a square and then used my nailer to add a few brad nails to tack it together.

After the glue dried, I used a bit more wood glue and my nailer to attach the top to the planter box.

Ithen flipped the planter upside down and attached the bottom slats with some wood glue and my nailer. I left spaces between the slats for drainage.

I used wood filler to fill in the nail holes and imperfections and then sanded the whole piece smooth.

I wiped the planter down with a tack cloth and then painted it with a few coats of Valspar’s Duramax Paint and Primer in Everglade Deck.

Once the planter was dry I was excited to get planting but I didn’t have any potting soil so I just placed a potted calla lily in the planter for now. Before I do put potting soil in the planter I plan to line the bottom with some landscaping fabric so that water can drain out between the slats but the soil wouldn’t fall through.

I’m really happy with how my planter came out and think it will add a little fun to my front porch. With this turning out successfully, I think I will have to make a second one to have a matching pair.

Note: I am posting as part of the Pinterest Challenge hosted by Young House Love, Bower Power, Sparkle Meets Pop and Red Bird Blue. If you posted anything for the challenge, please share your link with me!

DIY Square Beadboard Garden Planter…Supply List:1 – 2×2 @ 4 feet long, 1 – 1×2 @ 8 feet long, 1 – 1×3 @ 8 feet long, 1-1/4″ pocket hole screws, Brad nails, and Wood glue. Click picture for link to directions.




Related Articles

Back to top button

Adblock Detected

Please Close Adblock. Stay home ! Stay Safe !