Mobile Workbench with Table Saw – Bitcoin Value
Woodworking Crafts

Mobile Workbench with Table Saw


Mobile Workbench with Table Saw

.

.

Build a DIY mobile workbench with space for a table saw with these step-by-step plans.

This post may contain affiliate links. If you make a purchase from one of the links, I may make a small commission at NO EXTRA COST to you. This helps keep the tutorials and plans free here at Bitterroot DIY. Thank you for your support! See my full disclosure here.

** UPDATED 6/16/20 **

I’ve been working on getting my shop in order lately and finally built a couple workbenches. In case you missed it, last week I shared the plans for the new miter saw stand. My goal with the shop is to maximize space, but still be able to park the car in there when necessary. The miter saw stand is a permanent workbench at the back of the shop, but I also put together a DIY mobile workbench. It sits against the side wall when not in use (so the car fits), but I can move it anywhere in the shop when I’m working on a project. I built it around the table saw so it works as an out-feed table when I use the saw, but then I can lower the blade and use the whole table top. Win-win!

Enjoy the plans!

Step 1.

Assemble the bottom frame as shown below. Use 2 1/2″ self tapping screws through the frame to attach the 2x4s.

Pocket holes are a great option if you don’t want to see the screws from the front of the bench. However, since this is just a workbench, I simply screwed through the frame into the shorter 2x4s.

Step 2.

Attach the side legs to the bottom frame with 2 1/2″ screws. The bottom of the frame should sit flush with the bottom of the legs.

Attach the front and back legs to the frame and side legs with 2 1/2″ screws. I attached the side legs to the frame first and then drove a couple screws through the legs into the narrow side of the front and back legs to secure them together. You can see the approximate location of the screws in the diagram below.

Here’s a top view:

Put the bottom shelf in place on the bottom frame and attach with 1 1/4″ screws. Countersink the screws so they won’t get in the way.

It’s very difficult to put the bottom shelf in later (ask me how I know …), so definitely put it in before attaching the top frame in Step 3.

Step 3.

Build the top frame as shown. Use 2 1/2″ screws to attach the long sides to the supports.

Step 4.

Attach the top frame to the legs with 2 1/2″ screws.

I assembled the frame upside down to get top frame flush with the tops of the legs. Simply flip the bench over, move the new top frame into place, make sure everything is sitting flat on the ground, and attach the legs to the frame. No need to worry about clamping or balancing the top frame in mid-air while you try to attach it!

Step 5.

Assemble the frame for the table saw shelf with 2 1/2″ screws. Place those two center 2×4 supports wherever necessary to support the base of your table saw.

Step 6.

Place the shelf at the appropriate height for your table saw (mine was 11″) and attach to the workbench frame with 2 1/2″ screws.

Here’s a side view:

Step 7.

Use a jigsaw to cut the section for your table saw out of the table top. The dimensions shown work for my table saw. Adjust as necessary.

Step 8.

Attach the 2×4 feet to the legs with 2 1/2″ screws.

Fasten the locking casters to the feet with 1 1/4″ screws. I used washers on each screw since the screw heads were smaller than the holes in the caster wheels. You could also use washer head screws.

Step 9.

Center the tabletop and attach it to the frame with 1 1/4″ screws. There should be a 1 1/2″ overhang around the tabletop where it meets the legs.

Countersink the screws into the particle board so they won’t get in the way of your work.

Step 10.

I added a simple clamp rack along one end once the bench was finished.

Simply attach a small scrap board to the inside of the legs.

And there you have it!

Just a heads up – I built this bench to fit my Ryobi table saw. Make sure to measure your table saw and adjust accordingly.

Please let me know if you have any questions and I’ll get back to you as soon as possible!

If you’d like more information, I’ve also saved a video tutorial for this workbench to my highlights on my Instagram.

Thanks for stopping by!

For more project ideas, you can find me on Pinterest. And to stay up to date with the latest shenanigans, follow me on Instagram.

Build a DIY mobile workbench with space for your table saw with these plans. This mobile workbench is great to maximize your work area in a small space.

.

.

Tags

Related Articles

Back to top button
Close
Close

Adblock Detected

Please Close Adblock. Stay home ! Stay Safe !