How to Make a KitchenAid Cover – Bitcoin Value
Sewing Gifts

How to Make a KitchenAid Cover


How to Make a KitchenAid Cover

.

.

How to Make a KitchenAid Cover

I have been wanting to make one of these for ages. My KitchenAid gathers a lot of dust because to be honest I don’t use it that often. Nevertheless, I really wanted to make a cover for it so that on those occasions that I do use it I don’t have to spend a lot of time wiping it down. I knew that I could make a simple cover that fit in with the simple sewing ideas here at Sew Very Crafty. I opted to use a little pre-made piping to add a little extra to my cover but if you do not feel comfortable with that you do not need to add it.

The fabrics I used for my cover were cotton quilting weight fabrics that I got from JOANN Fabric & Craft Stores

What you will Need: How to make a kitchenAid cover

Pattern you can get here by clicking on this link

35″ x 16.5″ main fabric

2 pattern pieces of main fabric

35″ x 16.5″ lining fabric and fusible fleece

2pattern pieces of lining fabric and fusible fleece

1 Package of pre-made Piping (optional)

Step 1: Cut out your Fabrics

. I also used a fusible fleece to give my cover some structure. My fabrics came from JOANN Fabric & Craft Stores but you could head toorto get exactly what you need for your project. This post contains affiliate links that if you click on them and make a purchase I may receive a small commission at no extra cost to you.

Print the pattern. Tape the pattern pieces together by abutting them together and taping them. Cut two outer pieces, two lining pieces and two pieces of fusible fleece on the fold using the pattern pieces. These will be the ends of the cover. Cut an outer piece, a lining piece and fusible fleece that measure 35″ x 16.5″ for the body of the cover.

I used a directional fabric for my cover. In order for me to make sure that the pattern on the fabric was going in the same direction on both sides I cut the body fabric in half widthwise and restitched it using a 1/4″ seam allowance so that my fabric direction was facing up on both sides. Take care when using directional fabrics for this project.

Step 2: Fuse the Interfacing

Fuse the fleece to the outer body piece and the outer pattern pieces following the manufacturers instructions.

Step 3: Add your piping to the pattern pieces (Optional)

If you are adding piping to your cover add it to the outer pattern pieces by matching the raw edges of the piping to the raw edges of each piece. Pin the piping then baste to keep it in place.

Step 4: Add the body piece to the pattern pieces

The body piece is one long piece. Find the center of the long edge of the body piece and the center of the top of the pattern piece and pin them together. Continue pinning until the pattern piece is completely pinned to the body piece. There may be some excess body fabric left over but that is alright. After you have sewn the pieces together simply cut off the excess level with the pattern piece. Repeat for the other side. Stitch the outer body piece to the pattern pieces close to the piping. If you are not using piping. Stitch using a 1/4″ seam allowance. Turn right sides out.

If you are using piping, take out your zipper foot and stitch along the piping cord so that there is no bias binding showing and you just have the piping. This is much easier than it seems because you have the cording to guide your way. You can easily accomplish this my stitching just to the left of your basting stitches if you like.

Step 5: Create the lining

Repeat step three for the lining pieces without using the piping and leaving a 2″-3″ opening on one end of the lining for turning.

Step 6: Stitch the outer cover and Lining together

With right sides together place the outer cover and the lining cover together. Stitch all the way around the bottom using a 1/4″ seam allowance.

Step 7: Turn the cover

Turn the cover right sides out through the opening you left in the lining. Top stitch around the bottom of the cover. Close the opening in the lining using ladder stitch. I added some small stitches at the top of my cover and along the seams to secure the lining to the outer cover so it would not collapse within my cover. You have now finished your Kitchenaid cover.

I hope you enjoyed this project. If you would like more sewing and crafting projects sign up for our newsletter and receive access to our free printables library.

If you would like video tutorials of simple sewing projects subscribe to my YouTube channel

Like this: Like Loading…

How to Make a KitchenAid Cover I have been wanting to make one of these for ages. My KitchenAid gathers a lot of dust because to be honest

.

.

Tags

Related Articles

Check Also
Close
Back to top button
Close
Close

Adblock Detected

Please Close Adblock. Stay home ! Stay Safe !